Lawn Sprinklers Catalog Page 53, 54

• 12 interchangeable nozzles
• 40-360 degree adjustable arc with easy to adjust settings
• 6 5/8" Sprinkler body height, 4" Pop up height
• Pressure range is 30-70 PSI
• Covers from 29' to 46' radius at 40 PSI
• Water lubricated gear drive
• 3/4" Female Pipe inlet

This sprinkler is identical to the Hunter PGP sprinkler shown above but does not pop up. It comes with a full set of nozzles and is useful not only in a garden, but also in farms and greenhouses.
Note: Due to its height off the ground, the Shrub Sprinkler will also spray farther than the PGP pop-up sprinkler but will leave a dry area immediately around it for 2 to 4 feet. For even watering, use 100% overlap. If you use the PGPSH with the weighted sled base, use a P3412RN to adapt between the 1/2" FPT sled base outlet and the 3/4" FPT inlet on the sprinkler.

• 8 interchangeable nozzles
• 40-360 degree adjustable arc with easy to adjust settings
• 7 3/8" Sprinkler body height, 4" Pop up height
• Pressure range is 30-50 PSI
• Covers from 15' to 37' radius at 40 PSI
• Water lubricated gear drive
• 1/2" Female Pipe inlet
• (Note: This was previously called PGM)

This sprinkler is the same as the Hunter PGJ sprinkler shown above but does not pop up.   Although called a shrub sprinkler, it has a wide range of applicatons.   It can be used not only to cover a wide area in a garden but also in greenhouses, at the edge of a lawn where you do not want to bury a system or for farms that want overhead water. It covers large areas with minimal flow. Unlike most large area sprinklers, it has an adjustable arc so it can be at the edge of an area to be watered. Use with the weighted sled base or with PVC pipe. You will have a dry area immediately around the sprinkler, so either move the head back from where you want to water or have full overlapping coverage (head-to-head).

Hunter Sprinklers all require the same key to adjust the radius and to change nozzles. We ship one key with every six sprinklers. If you would like an extra key or a replacement key, they are sold separately

A swing joint has flexible fittings built into it that absorb shock exerted on the sprinkler.   They also make it easy to adjust the proper height, angle and placement for the sprinkler.

Even coverage and ease of adjustment make this a preferred product.   Comes with either the high flow red nozzle or a lower flow orange nozzle.   The radius is adjustable from 10 feet to 35 feet.   Has a 1/2" MPT base.

This very stable and moveable sprinkler stand has 1/2" female pipe threads to accept the Adjustable Gear Drive sprinklers and K-Rain Shrub Sprayer.   With hose threads on the inlet and outlet it can be hooked up in series using mainline tubing or to a garden hose.

This metal stake has hose fittings inlet and outlet.

A great way to adjust your sprinkler head height by hand. Without the use of tools, loosen the slip joint nut and adjust the sprinkler head to the desired height. Then retighten the slip joint nut. Always have the sprinkler head open to prevent water pressure build up.
Adjust from 12" to 23".
1/2" MPT x 1/2" MPT

This plastic stake has a 1/2" EasyLoc fitting on the side and a 1/2" MPT base on the top. It allows you to easily use 1/2" poly tubing with a Popup 4 sprinkler or any other fitting on a 1/2" MPT base. With a 1/2" FPT coupler the stake can be used with an Adjustable Gear Drive sprinkler which has a 1/2" MPT base.

This plastic stake has 1/2" EasyLoc fittings on each side and a 1/2" MPT base on the top. It allows you to easily use 1/2" poly tubing inline with a Popup 4 sprinkler or any other fitting on a 1/2" MPT base. With a 1/2" FPT coupler the stake can be use with an Adjustable Gear Drive sprinkler which has a 1/2" MPT base.