Greenhouse Kit
A misting kit to use for propagation in a greenhouse.
This kit is designed to spray 2 tables 10 feet long and 4 feet wide each.
It allows you to attach the tubing and misters above the propagation table
to trellis wire (not included).
Misters should be spaced every 2 feet or less.
Each mister comes with an anti-drip device that prevents misters from dripping
after the system shuts off.
The kit includes 50 feet of mainline tubing with fittings, filter, pressure regulator
and 10 Tornado misters with anti-drip devices.
Complete instructions included.
Kit includes:
- 1 - Check Valve (
FAVBH)
- 1 - Tee Filter (
FT200)
- 1 - 30PSI Pressure Regulator (
PRSG30)
- 1 - Female Hose Beginning (
ELFH)
- 1 - 50' Roll of 1/2" Mainline Tubing (
1250)
- 10 - Misting Assemblies (
MEBARB + MEAD + MTFGPR)
- 2 - Figure 8 Ends (
CF8)
- 1 - Easy Loc Tee (
ELT)
- 1 - Easy Loc Coupler (
ELC)
- 1 - Easy Loc Elbow (
ELL)
- 20 - Trellis Hangers (
STRE)
- 10 - Goof Plugs (
14GP2)
- 1 - Key Punch (
PUKEY)
|
|
| |
| Download kit instruction page |
Woodpecker 4-Way Splitter
This is a 4 way splitter for watering container plants
that fits on the outlet end of any pressure compensating
Netafim Woodpecker or Woodpecker Jr PC
emitter. You can then water four container plants from a single emitter.
Two of the splitters can be joined together to provide eight outlets by clipping
the top off one of the units and inserting it into the bottom of the other
splitter.
The typical layout uses special micro-tubing (DM100 or DM1000, below) and
an arrow dripper at the tube end.
The arrow dripper must be used to equalize the
flow from each outlet port and to hold the line in place.
|
|
DMPCA
|
| 1-99 | $0.18 | Each |
| 100+ | $0.16 | Each |
|
|
|
DMAR
|
| 1-99 | $0.18 | Each |
| 100+ | $0.16 | Each |
|
|
|
DNPCAP
|
| 1-9 | $0.16 | Each |
| 10-99 | $0.155 | Each |
| 100+ | $0.145 | Each |
|
|
|
|
| |
|
18100
|
100 feet micro-tubing
|
| |
|
18500
|
500 feet micro-tubing
|
| |
Woodpecker Multi-Outlet Dripper Assemblies
These multi-outlet assemblies attach to the outlet of a
Woodpecker or
Woodpecker Jr.
emitter and divide its flow evenly.
There are two types of assemblies, both of which have two 18" and two 30" tubes
with Arrow Drippers at the ends.
Since DMWASS has a flat, closed top, it must be used when four outlets are desired.
If eight, twelve or sixteen outlets are needed, the open-top, stackable assembly (DMWAST)
is used on the bottom, with the closed-top (DMWASS) on top.
Use the DNPCAP
to shut off the emitter when not being used.
Woodpecker emitters and Cap purchased separately.
|
|
|
DMWASS
|
4-Way Flat Assembly (use as the top splitter)
|
| |
|
DMWST
|
4-Way Stackable Assembly
(use except for top assembly)
|
| |
Anti-Drip Devices
When using overhead irrigation in greenhouses, each
sprinkler or mister assembly must have an anti-drip device
to prevent damage to plants directly below.
The anti-drip we carry is designed to be used two ways:
- Exp1. Directly into PVC pipe using a rubber
grommet (drill a 7/16" hole)
- Exp2. For insertion at the end
of 1/4" tubing or directly into 1/2" tubing using an Ein Dor barb
MEBARB
All parts to these hanging assemblies have press-fit
ends for easy installation.
Ein Dor Mini Sprinkler
heads have press fit bases and we stock special
Tornado Misters and
Tornado Mini Sprinklers with press fit bases
for this purpose.
NOTE: The anti drip device works in either direction.
|
Into PVC
Into Poly
|
| |
|
MEGRO
|
Grommet for PVC insertion
|
| |
| |
MEBARB
|
| 1-9 | $0.17 | Each |
| 10-99 | $0.15 | Each |
| 100+ | $0.135 | Each |
|
|
|
Tornado Misters - Press Fit Version
Press Fit misters do not go directly into your tubing.
They require either a MEBARB or a MECPL fitting as illustrated above.
They can also go into the
Ein Dor Support Kits, which come
with a MEBARB fitting.
(Flows at 40 PSI)
|
|
MTFGPR - Tor Fogger, Green, Press Fit
MTFBPR - Tor Fogger, Press Fit
|
| 1-99 | $0.48 | Each |
| 100+ | $0.44 | Each |
|
|
Tornado Mini Sprinkler - Press Fit Version
The press-fit Tornado Mini Sprinklers give you some additional options.
They require a
MEBARB
fitting, which is available either as part of
the Ein Dor Support Kit
or can be purchased separately.
Tornado Mini Sprinklers
| Sprinkler |
Color |
Flow
@ 20 PSI |
Radius
@ 20 PSI |
Flow
@ 30 PSI |
Radius
@ 30 PSI |
| MTMSRPR |
Red |
21 GPH |
6 feet |
26 GPH |
7 feet |
| MTMSWPR |
White |
25 GPH |
6.5 feet |
30 GPH |
8 feet |
Flow rates below rated at 20 PSI
|
|
MTMSWPR - White 25 gph
|
$0.52 each
|
|
Plastic Weights
Clips onto 1/4" or 1/8" line.
A safe replacement for lead weighted emitters.
Use with any 1/4" emitter.
|
|
DNWGT
|
| 1-99 | $0.27 | Each |
| 100+ | $0.25 | Each |
|
|
|
Inverted Mini Wobbler
Specially designed for overhead applications.
- Great for seed propagation
- Outstanding Uniformity - Fine Spray
- Pipe Thread: 1/2" Male Pipe Thread
- Flow Rates: 0.3 to 2.5 GPM
- Operating Pressure: 15-40 PSI
Inverted Mini Wobbler
| Part |
Color |
GPH
@ 20 PSI |
Radius
@ 20 PSI |
GPH
@ 30 PSI |
Radius
@ 30 PSI |
| MWIG |
Gold |
57 GPH |
11 ft |
82 GPH |
11 ft |
| MWIBG |
Beige |
45 GPH |
11 ft |
55 GPH |
11 ft |
Radius is at 6 feet above the beds
Flow rates below rated at 20 PSI
|
Anti-Drip
|
|
MWIG
|
Gold 57 GPH, 11ft radius
|
| |
|
MWIBG
|
Beige 45 GPH, 11ft radius
|
| |
| |
|
|
Kits 
Checkout