Female Hose Beginning (Swivel End)
Use to attach mainline tubing to a faucet, hose end or
male hose end of a filter or adapter.
The most common way to start a system.
|
|
| |
Coupler
For joining mainline tubing or to repair a slit or large
hole in a mainline.
A necessary repair part.
Always have a few on hand.
|
|
| |
Male Hose End with Cap
This fitting is used to end a line.
The screw off cap makes it easy to flush lines.
|
|
| |
Male Hose End
A fitting with male hose thread.
If you want to flush your lines after each watering,
use a Male Hose End with a Flush Valve, part
VFH).
|
|
| |
Female Hose Plug
Protect your system from dirt and bugs when it is disconnected
from the water source (i.e. during winter shut down
or when alternating systems with a single water feed line).
Male hose thread for female hose beginning (CHS,
ELFH Hose Beginning).
|
|
| |
Figure 8 End
The most common fitting used to end a line.
Simply slip over the end of the line, bend the
tubing over, and slip over the end again.
|
|
| |
Tee
To add an additional line to any area, simply cut the mainline tubing and insert a Tee.
|
|
| |
Female Hose Tee (Swivel End)
Attach to a hose or hose bib where two mainlines are needed.
|
|
| |
Easy Loc Male Hose Tee
Easy Loc tee with male hose thread beginning. Use to install a
flush valve (VFH) at
the low point of a 1/2" mainline system.
|
|
| |
Elbow
To go around a corner that would otherwise kink the mainline tubing.
|
|
| |
Female Hose Elbow (Swivel End)
For situations where there is no room to use a straight fitting to start a system.
|
|
| |
1/4" Barb
Connect a 1/2" line to 1/2" or 3/4" mainline
tubing without using a Tee.
Make a hole in the mainline tubing with a 1/4"
punch and insert the barb.
Great for making a loop of In-line Emitter
tubing around a tree.
The flow through this 1/4" barb is around 80 GPH.
NOTE: This is an oversized barb, do not use with 1/4" tubing.
|
|
| |
3/8" Barb
To connect 1/2" mainline tubing to
3/4" mainline without using a Tee.
This fitting allows a higher flow than the EL14B.
Use a .400 Barb Punch ( PU400).
|
|
| |
3/8" Barb Grommet
To connect a 3/8" barb into 1" or larger PVC pipe.
Rubber grommet makes a water tight seal.
Drill a 9/16" hole in the PVC.
|
|
| |
Easy Loc 1/2" Valve
This is a new valve with a full port that will allow
higher flows and can withstand higher pressures.
Easy to grip handle.
|
|
| |
Easy Loc Cross
A 4 way Easy Loc fitting for 1/2" mainline tubing.
|
|
|
|
Easy Loc Side Out Ell
An easy and unique fitting for going up and around
posts or to use from above on a misting system.
90° for each side.
|
|
| |
Easy Loc .700 OD X .620 OD Coupler
For joining the smaller Raindrip (.620 OD) tubing to our
standard 1/2" mainline tubing (.700 OD).
|
|
| |
Easy Loc x PVC Pipe Thread
1/2" Male Pipe Threads
To attach 1/2" mainline tubing to any 1/2" female pipe threads.
|
|
| |
1/2" Male Pipe Threads with Valve
Male pipe threads inlet with a valve allows you to shut off individual rows.
|
|
| |
3/4" Male Pipe Threads
To attach 1/2" mainline tubing to a 3/4" valve or any 3/4" female pipe threads.
|
|
| |
1/2" Female Pipe Tee
Use to attach 1/2" mainline tubing to any PVC male pipe thread outlet. Not a swivel.
|
|
| |
3/4" Female Pipe Threads
To attach 1/2" mainline tubing to a 3/4" Y type filter
or any 3/4" male pipe hreads.
Not a swivel.
|
|
| |
PVC Pipe Adapters
|
|
1/2" PVC Slip
Glue into any 1/2" PVC fitting to make your own 1/2" Easy Loc Fitting.
|
|
| |
3/4" PVC Slip
Glue into any 3/4" PVC fitting to make your own 1/2" Easy Loc Fitting.
|
|
| |
Tee x 3/4" PVC Slip
Easy Loc Tee with 3/4" PVC slip inlet to run two 1/2" mainlines from a 3/4" PVC riser
|
|
| |
Raindrip Users
We also carry various Easy Loc fittings for
Raindrip sized tubing.
Prices are the same as our standard fittings.
The parts available for 620 O.D. are listed here.
Please order by these product codes.
|
|
|
620ELFH
|
Female Hose Beginning
|
| |
| |
| |
| |
| |
|
620ELMC
|
Male Hose End w/cap
|
| |
| |
| |
|
|
Kits 
Checkout