Take Apart Emitter
The DTA1, DTA2 and DTA4 Take Apart emitters can be pulled apart for easy cleaning.
The 1/4" barbed inlet can be plugged directly into
a mainline or attached to the end of 1/4" tubing.
The outlet is a 1/4" barb.
They also work very well with low pressure gravity systems.
IMPORTANT NOTE: The flag end is the outlet, the beveled barb end is the inlet.
|
|
DTA1 - 1 GPH (black #4)
DTA2 - 2 GPH (blue #8)
DTA4 - 4 GPH (green #16)
|
| 10-99 | $0.22 | Each |
| 100+ | $0.20 | Each |
|
|
Take Apart Punch and Insert Tool
This punch is designed to be used only with the
Take Apart Emitters above.
Makes insertion much easier!
|
|
| |
Mini Quart Dripper
The Mini-Quart is a special low flow dripper that works
great for smaller containers and xeriscape plantings.
They can be inserted
directly into mainline tubing or used at the end of 1/4" tubing.
This 1/4 GPH emitter is the lowest flow single outlet emitter available.
|
|
If you're buying for a Water4Gas installation, click this button:
|
DQT
|
| 10-99 | $0.21 | Each |
| 100+ | $0.198 | Each |
| |
|
Pot Dripper
The DPOT12 and DPOT1 emitters are basic container drippers with a 2 inch hold
down stake and a 1/4" threaded inlet.
NOTE: A 1/4" transfer barb (14TB) and
1/4" tubing are needed to connect this emitter to the mainline.
These also can be used with 1/8" tubing.
|
|
DPOT12 - Pot Dripper 1/2 GPH, red
DPOT1 - Unavailable until mid August
|
| 1-9 | $0.35 | Each |
| 10-99 | $0.32 | Each |
| 100+ | $0.297 | Each |
|
|
Hanging Basket Dripper
The DH12 and DH1 emitters are ideal for watering hanging baskets.
Connect the 1/4" barb to a 1/4" line dropped
from an overhead mainline and insert the 5" stake into the soil.
|
|
DH12 - Hanging Basket 1/2 GPH, black
DH1 - Hanging Basket 1 GPH, black
|
| 1-9 | $0.42 | Each |
| 10-99 | $0.37 | Each |
| 100+ | $0.35 | Each |
|
|
In Line Emitter
The DMIL12, DMIL1 and DMIL2 are the only emitters that can be strung together.
Use these drippers when you want to make your own
In-Line emitter tubing out of 1/4" tubing.
For unevenly spaced plants or where multiple emitters
are needed for larger plants just add more emitters.
It's also easy to add these emitters into
existing 1/4" lines at any time.
To use, cut the 1/4" tubing where you want an
emitter and insert the barbed ends into the tubing.
Use a goof plug to end the line.
Remember: 1/4" tubing can only carry about 30 GPH,
so don't put too many emitters in a single 1/4" feed line.
|
|
DMIL12 - In-ine Emitter 1/2 GPH, yellow
DMIL2 - In-ine Emitter 2 GPH, blue
DMIL1 - In-Line Emitter 1 GPH, black
|
| 1-9 | $0.36 | Each |
| 10-99 | $0.35 | Each |
| 100+ | $0.32 | Each |
|
|
Non-Plugging Emitter
If you have a very dirty water supply (pond or irrigation ditch) where a fine screen
filter clogs quickly, this may be the answer. Use a coarse screen filter (30-50 mesh)
for large particles and the Non-Stop Emitter will pass particles that would plug almost
any emitter.
A minimum of 15 PSI is required for these emitters to work properly.
Use at the end of 1/4" tubing or installed directly into the mainline.
Will emit 1 GPH at 20 PSI.
|
|
DNS1
|
| 1-9 | $0.70 | Each |
| 10-99 | $0.63 | Each |
| 100+ | $0.59 | Each |
| |
|
|
|
Kits 
Checkout