Female Hose Beginning
(Swivel End)
Use to attach mainline tubing to a faucet, hose end or male
hose end of a filter or adapter.
|
|
| |
Coupler
For joining mainline tubing or to repair a slit or large hole
in a mainline.
A necessary part used to repair drip irrigation systems.
Always have a few on hand.
|
|
| |
|
For joining 1/2" to 3/4" mainline tubing.
|
|
CRCC
|
Reducing Coupler 3/4" x 1/2"
|
| |
Male Hose End with Cap
This fitting is used to end a line.
The screw off cap makes it easy to flush lines.
|
|
| |
| |
Female Hose Plug
Protect your system from dirt and bugs when it is disconnected
from the water source (i.e. during winter shut down
or when alternating systems with a single water feed line).
Male hose thread for female hose beginning (CHS,
SMLFH Hose Beginning).
|
|
| |
Figure 8 End
The most common fitting used to end a line.
Simply slip over the end of the line, bend the
tubing over, and slip over the end again.
|
|
| |
Female Hose Beginning Elbow
(Swivel End)
For situations where there is no room to use a straight
fitting after the filter.
|
|
| |
Female Hose Tee
(Swivel End)
Attach to a hose or faucet where two mainlines are needed.
|
|
| |
Tee
Use to branch off mainline tubing.
|
|
| |
|
CT3412
|
3/4" x 3/4" x 1/2"
|
| |
Compression x 1/4" Barb
Connect a low flow 1/2" line to 1/2" or 3/4" mainline tubing
without using a Tee.
Make a hole in the mainline tubing with a 1/4" punch
and insert the barb.
Use this to make a loop of In-line Emitter tubing
around a tree.
The flow through this 1/4" barb is around 100 GPH.
Do not use with 1/4" tubing.
|
|
| |
Elbow
(90 degree bend)
To go around a corner that would otherwise kink the mainline.
|
|
| |
Cross
|
|
| |
|
CX3412
|
3/4" x 3/4" x 1/2" x 1/2"
|
| |
Compression Shut Off Valve
Shut off any 1/2" mainline by simply turning the valve
handle a quarter turn.
This is a low pressure valve and may leak above 30 PSI.
If a higher pressure is necessary, see the Green Back Valve.
|
|
| |
Male Hose End
(Male hose thread)
|
|
| |
Male Hose Tee
Use this fitting with a hose shut off (HSO) and a (CHS)
as a way to shut off an individual bed or row.
|
|
| |
Compression Adapters to PVC
Compression 1/2" x 3/4" FIP
(Female Pipe Thread)
To attach mainline tubing to 3/4" Male Pipe Threads.
|
|
| |
Compression 1/2" x 3/4" MIP
(Male Pipe Thread)
To attach mainline tubing to 3/4" Female Pipe Threads.
|
|
| |
Compression Adapter
1/2" compression into PVC. Glue into any 1/2"
PVC slip fitting to convert it to a compression fitting.
|
 CA
 CSA
|
|
CA
|
1/2" compression into 1/2" PVC
|
| |
|
CSA
|
1/2" compression into 3/4" PVC
|
| |
Compression x PVC Pipe Adapter
For attaching 1/2" mainline tubing directly into 1" or larger PVC.
The adapter comes with a rubber grommett for sealing
around the hole.
Drill a 9/16" hole in the PVC.
Insert the grommet into the PVC and then insert the 3/8"
barb into the grommet.
|
|
| |
Raindrip Users
Compression Coupling Adapter
To go from smaller 1/2" tubing (.620 OD - Raindrip, Accudrip, etc.)
to our standard 1/2" tubing (.700 OD).
|
|
| |
We also carry various Compression fittings for Raindrip sized tubing.
Prices are the same as our fittings and those available are listed below.
|
|
|
620CHS
|
.620 Female Hose Beginning
|
| |
| |
| |
| |
| |
|
620CETC
|
.620 Male Hose End
|
| |
|
620CA
|
.620 Compression Adapter
|
| |
|
|
Emitters 
Checkout 
Call 
